Supplies Needed
Before getting started, you will need some items to thread a Singer handheld sewing machine. Firstly, you need the sewing machine itself, and the manual that came with the machine, or a sewing machine manual for the machine you own. You will also need good quality thread in the color you wish to sew with, a pair of scissors, a small screwdriver or a seam ripper, thread clippers, and a bobbin.
Preparing the Machine
Before threading the machine, it must be prepared. To start, check to make sure the needle is in the highest position that it can go and that the thread take-up lever is also in the highest position. This will make the task of threading much easier. Then, loosen the needle clamp screw, so that the needle can be replaced easily. Then loosen the presser foot lever and the presser foot screws.
Thread the Needle
Once the machine is set up, you can begin threading the needle. Firstly, cut a piece of thread of about 24 inches. Thread this through the eye of the needle. Then, wrap the thread around the screw in the back of the machine. Make sure to do this three or four times. Push the thread through the notch on the thread guide at the front of the machine. Pull the thread slightly up and underneath the thread take-up lever. Push the thread around the thread guide, underneath the tension discs, and then through the spring guide. Finally, thread the needle from the left to the right.
Thread the Bobbin
Once the needle is threaded, the bobbin must be threaded. Start by inserting the bobbin into the bobbin case. Then, cut a piece of thread that is about six inches long. Pull the thread through the hole in the bobbin and press down on the bobbin’s tension lever. Place the thread onto the bobbin separator and pull the thread underneath the separator plate. Place the thread under the right side of the bobbin finger and then thread the thread clockwise around the second thread guide. Pull the thread diagonally across the bobbin and thread it through the bobbin thread guide. Finally, pull the thread back through the slit in the bobbin case.
Pulling the Thread Through the Machine
Once the bobbin is threaded, the thread will need to be pulled up and through the machine. Begin by pressing the reverse switch and opening the cover of the bobbin case. Hold the bobbin thread and press the reverse switch again to rotate the feed or shuttle race. Move the thread up and out of the shuttle race. Push the thread around the upper thread guide. Hold onto the thread and turn the handwheel so that the needle moves down. Pull the thread slightly and the bobbin thread should be automatically pulled through the needle plate.
Preparing to Start Sewing
Once the thread is pulled through the needle plate, you can start preparing the machine for sewing. Securely tighten the needle clamp screw with a screwdriver or a seam ripper. Push the thread to the back of the presser foot and raise the presser foot lever into a locked position. Finally, close the cover of the bobbin case. Now, the machine is ready to start sewing.
Securing the Thread
Before you start sewing, you must secure the thread at the end of the fabric you are working on. To do this, loop the thread around the spool pin a few times and then turn the handwheel so that the needle moves down and the thread is pulled through the fabric. After a few stitches, go back and check that the thread is secure. If it is not, you will need to pull the bobbin thread through the needle plate and start again.
Cleaning the Machine
To keep your Singer handheld sewing machine in good working condition, it is important to clean it regularly. To begin the cleaning process, unplug the machine and remove the needle. Thread clippers can be used to remove any threads that are tangled or caught in the needle. Then, wipe the machine down with a damp cloth or use an air compressor to blow away any dust or particles from the machine.
Checking the Machine Regularly
Regularly checking your Singer handheld sewing machine can help to make sure that it is in good working order. Before sewing, make sure to check the pressure and tension on the machine. Make sure that the tension discs are correctly adjusted and that the pressure is set correctly. Check the needle, too, to make sure that it is not bent and that it fits correctly into the needle clamp.
Parts of the Machine
One of the most important aspects of threading a Singer handheld sewing machine is understanding the parts of the machine. Many machines have an arm, a bedplate, a bobbin, a bobbin housing, a needle plate, a presser foot, and a thread take-up lever. Each part of the machine is necessary for proper machine operation and threading.
Threading Tips
When threading a Singer handheld sewing machine, there are a few tips that should be followed. Firstly, make sure to use good quality thread, as low quality thread can cause issues and clogs in the machine. Secondly, be sure to read the manual that came with the machine and follow the instructions. This will ensure that the machine is threaded correctly and that it runs smoothly. Lastly, be sure to regularly clean and check the machine for any problems.
Storing the Thread
When you are finished sewing, it is important to store the thread correctly. Place the thread in a dry, cool place away from direct sunlight. This will help to prevent the thread from becoming brittle and damaged. Additionally, it is best to store thread on a spool or in a container so that it does not become tangled.
Stitching Techniques
Using the correct stitching techniques is important when sewing with a Singer handheld sewing machine. To start, choose the correct stitch length and width for the fabric that you are working with. Additionally, make sure to practice the technique to ensure that it is done properly and that it looks neat. Finally, make sure to use the correct tools when stitching, such as a seam ripper, thread clippers, and scissors.
