Preparing the Bobbin
Before you can insert the bobbin into the Brother sewing machine, you must first make sure it is correctly prepared. Begin by selecting the bobbin thread that matches the fabric you are sewing with. Hold the thread next to the fabric and check that the color is close to the same, as any difference in hue may be visible in your stitching. Next, cut a piece of thread the same length as your arm, allowing you some slack. Put the thread in the bobbin, looping it around the bobbin several times. Once you have looped the thread onto the bobbin, pull it firmly through so the thread wraps around the bobbin. Pull the thread firmly, but do not yank or pull it too tight as this can damage the thread or the bobbin.
Installing the Bobbin in the Sewing Machine
Next, check that you have the correct bobbin part for your sewing machine. Your machine should have come with several interchangeable parts, and you should have chosen one that corresponds with your machine. Insert the bobbin part into the slot in the sewing machine and turn the hand wheel towards you. Once the needle has dropped to its lowest point, loosen the thread by pulling it slightly. Now, open the front cover of the machine and insert the bobbin, allowing the thread to slide over the slot. Then, pull the bobbin out and thread it through the slot as you turn the hand wheel. Finally, insert the bobbin and close the cover.
Threading the Bobbin
The next step to insert the bobbin into the Brother sewing machine is to thread the bobbin. To do so, hold the top thread in your left hand, and the bobbin in your right. Pull the thread through the guide and down the right side of the bobbin near the center. Then, take the thread around the ridge of the bobbin and then down and across the surface of the bobbin to the left side, layering it with the thread from the previous step. Now, pull the thread from the bobbin up in a loop, and bring the tail toward you so that the thread forms a “T” shape. Finally, thread the needle, and you should hear the bobbin thread being pulled up as you do so.
Double-Checking Thread Tension
When you have finished threading the bobbin, it is important to double-check your tension. To do this, raise the presser foot and place a small piece of fabric underneath it. Gradually turn the hand wheel, starting from the 2 o’clock position and going counterclockwise until the bobbin thread starts to rise to the very top of the fabric. If the thread starts to loop over itself, it means that the tension is too tight and you need to adjust it. You can do this by turning the small knob on the side of the machine with a screwdriver. Alternatively, if the thread does not appear on top of the fabric, then it means the tension has become too loose and needs to be tightened.
Remembering to Thread the Needle
Before you start to sew, it is important to remember to thread the needle. This will ensure your fabric is fed through the machine properly, and will make all the difference to the finish of your item. To do this, hold the spool of thread in your right hand, and the thread in your left hand. Pass the thread over the tension disc and pull it to the back of the machine. Now, hold the thread in your right hand and guide it towards the left side of the machine, looping it through the threading guide before bringing the tail forward and inserting the thread into the eye of the needle. Once you have done this, double check that the needle is threaded properly by tugging gently on the thread and making sure it does not come undone.
Procedure to Follow for Bobbin Winding
The bobbin is also an integral part of setting up the Brother sewing machine correctly. Before you can sew, you must wind the bobbin, which can be achieved by following the below procedure. Firstly, ensure that the machine is in the bobbin winding mode and that the bobbin is correctly charged with thread. Next, guide the thread over the tension disc and pass the tip of the thread through the hole in the center of the bobbin. Then, hold the bobbin in one hand and turn the hand wheel towards you in a counterclockwise motion until the bobbin is full. Finally, remove the thread from the hole in the bobbin, and your bobbin is ready to use.
Careful Bobbin Removal
When it comes to removing the bobbin from the machine, always make sure to do so with care. To remove the bobbin, turn the hand wheel towards you until the needle is at its lowest point. Then press the bobbin release lever and take the bobbin out of the machine. Make sure to hold the thread lightly when removing the bobbin, as to not cause any damage to the bobbin or the thread.
Proper Storage and Maintenance
Another important aspect of inserting the bobbin into the Brother sewing machine is storing and maintaining the machine correctly. Before storing the bobbin, check that it is clean, and that all lint or bits of fabric have been removed. Store the bobbin in its original packaging or in an airtight container. Regularly check your sewing machine for lint and other debris which can become trapped in the feed dog and the bobbin case. Cleaning the bobbin case should be done every 6 months, and should be done more frequently if you use the machine often.
Carry Out Regular Maintenance
Signs that your sewing machine is in need of maintenance include difficulty in threading, stitches that are too tight, or fabrics that do not feed properly. If this is the case, then it is worth getting your sewing machine serviced by a professional. Regular maintenance and servicing can help ensure that the machine continues to work efficiently and that problems can be spotted before they become more serious.
Patience and Careful Checklist
When it comes to inserting the bobbin into the Brother sewing machine, patience and thorough checking are key. Make sure that the bobbin is correctly prepared, correctly inserted into the machine, correctly threaded, and correctly wound. Additionally, one should remember to thread the needle and carry out regular maintenance of the machine before storing the bobbin away safely. Following these simple steps will guarantee successful bobbin insertion, and make sure that your finished work looks its best.
