Merritt Singer sewing machines are some of the most reliable and long-lasting machines available for sale today. These machines are easy to work on and use, and need very little oiling to keep them running smoothly. This guide will help you oil your Singer Merritt machine the right way, to keep it in optimal working condition.
The first step is to remove the faceplate from the machine. This can be done by removing the screws that attach it to the body and then lifting it off. Once the faceplate has been removed, locate the tension control screw, which is located near the bobbin winder. Turn this screw counter-clockwise until it is loose and can be moved freely.
The next step is to locate the crank-shaft and its lubrication points. This is a small black wheel on the side of the machine, towards the back. It will have a few small holes on either side, which is where the oil needs to be applied. The crank-shaft will also have small set screws on the sides. These need to be removed in order to access the lubrication points.
Once the set screws have been removed, use a small oil can to apply a few drops of light machine oil or 3-in-1 oil onto the lubrication points. Be sure not to over-oil, as this can cause damage to the internal parts of the machine. After the lubrication points have been oiled, replace the set screws and tighten them back into place.
The next step is to reattach the faceplate to the body of the machine. To do this, reconnect the screws and tighten them into place. Finally, turn the tension control wheel clockwise until it is tight, and test out the machine to make sure it is running properly.
By following these simple steps, you can easily oil your Singer Merritt sewing machine. It is important to oil your machine on a regular basis, as this helps to keep the internal components from wearing down and increase its lifespan. Remember, always use light machine oil or 3-in-1 oil for best results.
Removing the Bobbin Area
The bobbin area of a Singer Merritt sewing machine is located underneath the feed-dog cover plate. To access this area, the cover plate needs to be removed. To do this, first locate the two screws at the back of the machine and loosen them. Once they have been loosened, the cover plate can be detached and set aside.
The next step is to locate the lint catcher and its associated spring. The lint catcher is a small plastic piece that can be found near the bobbin area. To clean this piece, first use a vacuum cleaner to remove any lint or dust that has gathered in this area. Once the lint has been removed, use a cotton swab and light machine oil to lubricate the spring. After this has been done, replace the lint catcher and spring, and reattach the cover plate.
Cleaning and Oiling the Hook Race
The hook race is the part of the machine that facilitates the winding and curling of the thread around the bobbin. To properly clean and oil this part of the machine, first loosen the top screw, which is located near the tension control wheel. Once this has been done, the hook race can be lifted off the body of the machine.
The next step is to use a cotton swab and light machine oil to lubricate the hook race. Work the swab in circles and cover the entire surface, applying more oil as needed. After the hook race has been lubricated, wipe away any excess oil with a dry cloth, and then reattach it to the machine.
Be sure to use light machine oil when oiling the hook race, as heavier oils can cause gunk to build up and damage the internal components.
Cleaning and Oiling the Needle Bar
The needle bar is the part of the machine that connects the needle to the shuttle and helps the needle to move up and down. To properly clean and oil this part of the machine, first loosen the screws that attach it to the body of the machine. Once these screws have been removed, the needle bar and its associated parts can be lifted off the machine.
The next step is to use a cotton swab and light machine oil to lubricate the needle bar and its associated parts. Work the swab in circles and cover the entire surface, applying oil as needed. After the needle bar has been lubricated, wipe away any excess oil with a dry cloth and reattach it to the machine.
Again, be sure to use light machine oil when oiling the needle bar, as heavier oils can cause gunk to build up and damage the internal components.
Cleaning and Oiling the Tension Discs
The tension discs on a Singer Merritt sewing machine are located near the tension control wheel. To access these discs, first unscrew the tension control wheel and then remove the C-ring. Once the C-ring has been removed, the tension discs can be lifted off the machine.
The next step is to use a cotton swab and light machine oil to lubricate the tension discs. Work the swab in circles and cover the entire surface, applying oil as needed. After the discs have been lubricated, wipe away any excess oil with a dry cloth and then reattach them to the machine.
It is important to use light machine oil when oiling the tension discs, as heavier oils can clog up the discs and cause damage to the internal parts of the machine.
Cleaning and Oiling the Bobbin Case
The bobbin case on a Singer Merritt sewing machine is located near the tension control wheel. To properly clean and oil this area, first unscrew the tension control wheel and then remove the C-ring. Once the C-ring has been removed, the bobbin case can be lifted off the machine.
The next step is to use a cotton swab and light machine oil to lubricate the bobbin case. Work the swab in circles and cover the entire surface, applying more oil as needed. After the bobbin case has been lubricated, wipe away any excess oil with a dry cloth and then reattach it to the machine.
Remember to use light machine oil when oiling the bobbin case, as heavier oils can cause gunk to build up and damage the internal components.
