Step 1: Prepare the Sewing Machine For Threading
Before you attempt to thread the bobbin, you must prepare the machine for threading. To begin with, make sure the sewing machine is unplugged. Then, use a screwdriver to remove the top plate. Next, lift up the bobbin plate. Using the release lever, remove the bobbin from the case.
Step 2: Thread The Bobbin On A Sewing Machine
Once the machine is prepped, you’re ready to thread the bobbin. Place the bobbin on top of the bobbin-winding spindle, with the thread winding on the side of the bobbin. Then, press down on the bobbin-winding spindle, and match the top threading point with the bobbin. Once the points are aligned, insert the end of the machine’s thread into the threading point. Gently turn the bobbin-winding spindle to the right until the thread becomes taut.
Step 3: Wind The Thread Around The Bobbin
Once the bobbin is securely in place, it’s time to start winding the thread around the bobbin. Using the hand wheel, start to rotate the bobbin-winding spindle very slowly. As you do this, the thread will wind around the bobbin. Go slowly, paying close attention to the thread as it winds. Once the thread has completely wrapped around the bobbin, it’s time to move onto the next step.
Step 4: Clip The Thread
Once the bobbin is full, the next step is to cut the thread from the bobbin. To do this, use sharp scissors to carefully clip the thread at the end of the spindle. Then, pull the bobbin away from the spindle.
Step 5: Reassemble The Top Thread
To finish up the threading process, reassemble the top thread. If you had to remove the top plate, make sure to put it back in place. Then, take the thread from the bobbin and thread it through the main thread guide. From there, go around the tension discs before inserting the needle into the thread. Finally, place the thread around the take-up lever, and pull it up towards the top of the machine.
Step 6: Control The Tension
Once the bobbin is threaded, it’s essential to adjust the thread tension. The way you adjust the tension is by turning the thread tension dial. When you do this, you’ll want to hear four clicks. If you’re not hearing these clicks, the thread tension is too tight and you’ll need to loosen the tension dial.
Step 7: Sewing With The Bobbin
Lastly, you’re ready to start sewing with the bobbin. To do this, you’ll need to lower the presser foot, lower the feed dog and raise the bobbin thread. After that, you can start sewing as desired.
Tips For Threading The Bobbin
If you’re having a hard time threading the bobbin, here’s a few tips to keep in mind. Firstly, make sure to use the right type and weight of thread for the bobbin. If you’re threading a bobbin made of plastic, use thread made specifically for plastic bobbins. Secondly, never pull on the thread too tightly, or else it’ll break. Thirdly, if you’re having a hard time threading the bobbin, try switching to a different thread. Finally, make sure to keep the bobbin tension adjusted correctly. If the bobbin is too tight, it will cause the seams to pull together or become too loose.
Bobby Winding Tips
When winding the bobbin, it’s important to take your time and go slowly. If the bobbin is wound too quickly, the thread may become tangled or the tension is too tight. If this happens, you’ll have to redo the winding process. Additionally, it’s helpful to use medical-grade tweezers to keep the thread from slipping off the bobbin. Finally, make sure the thread is being wound in a consistent manner. This will help keep the bobbin from becoming too tight or too loose.
Thread Storage Tips
When not in use, make sure to store the thread or bobbins in a dry place. Additionally, make sure the thread is carefully reeled onto the bobbin in a counterclockwise direction with even tension. If possible, store the thread in the original plastic wrap or package. This will help keep the thread free from dirt and dust.
Thread Lubrication Tips
Every so often, it’s important to lubricate the thread. This helps attenuate static electricity and helps the thread to flow freely. Before lubricating the thread, be sure to test the lubricant on a piece of scrap fabric. This will help you determine if a thread lubricant is needed.
