How to oil a Janome Sewing Machine Youtube
In a world full of expensive, fancy technologies, a humble sewing machine can be a great investment. Janome products are no exception, as they are reliable and easy to maintain. To keep your machine in its best condition and extend its lifespan, it’s important that you oil it regularly. Doing so can also improve your sewing experience and help you achieve better results. Luckily, it doesn’t take much effort to keep your Janome machine running smoothly. Here’s how to oil it properly according to a Janome official.
The first step to oil your sewing machine is to place it on a hard, flat surface. Then, you unplug the machine and remove the bobbin case. After doing so, an oil hole should be visible. Insert a few drops of oil into this hole, then give the oil a few seconds to settle in.
Next, pick up the handwheel and move it forward and backward a few times. This helps the oil disperse and work its way around the internal components. Do this for about 20 seconds, then wipe away any excess oil from the surface of the machine with a soft cloth.
If the machine has been used heavily, you may need to take a few additional steps. Put a drop of oil inside the bobbin case and around the race, then replace the bobbin case in the machine. Oil the entire area generously, and use an old toothbrush or a thin, flat-head screwdriver to scrape off old oil and dirt. Finally, use a lint-free cloth to wipe all the pieces.
Finally, use a clean cloth to clean the presser foot holder, foot control, and other parts of the machine that you’ll be using. You’ll then be ready to use your Janome machine as usual. Oiling your machine will only take a few minutes of your time, but it’s an important part of keeping it in excellent condition.
How to Clean a Janome Sewing Machine YouTube
Regular cleaning is just as important as oiling when it comes to maintaining a Janome sewing machine in good condition. As such, it’s important to know how to clean it properly for optimal performance and lasting durability. A Janome representative suggests this method.
Start by turning off the machine and unplugging it to avoid accidents. Then, use a lint-free cloth to wipe any visible dirt or marks off the machine. It’s also a good idea to vacuum the interior parts, especially if the machine has been used heavily. Additionally, remove any threads and lint with tweezers.
When that’s done, use a soft brush to clear any dust and particles from the bobbin case and bobbin holder. You’ll also need to clean the underneath of the presser foot and the feed dogs. You can use a cloth or a soft brush for this step. Finally, thoroughly clean the exterior of the machine with lint-free cloth.
Doing this regularly will help keep your machine in an excellent condition and make sure it functions correctly. Additionally, if your machine still has any build-up of dust or dirt, you may need to disassemble and clean it manually. However, this step should only be done if you’re experienced in the matter.
How to Lubricate a Janome Sewing Machine YouTube
Just like oiling, lubricating a Janome sewing machine is essential for optimal performance, avoidance of wear and tear, as well as a long life span. This easy process should not take more than five minutes of your time and can provide great results.
Start by turning off the machine and unplugging it to make sure no accidents occur. Then, unscrew the external screws to open the machine, and you’ll see the moving parts of the motor. Take a thin metal object, such as a pin or a thin wire and dip it in lubricant. Place a few drops of lubricant in each part that moves, making sure you cover all of them.
It’s also a great idea to lubricate the threading lever, needle plate, and all the other parts of the machine. Remember to use only lubricants specifically designed for janome machines and follow the instructions on the product. When you’re done, put the external screws back in place and make sure all the parts fit together accurately.
The last step is to run a test on the machine to check if anything needs additional lubrication. If not, your Janome machine should be prepared to use as usual. Although it might take some time and effort, lubricating your machine will ensure the best performance and protect it from wear and tear.
How to Thread a Janome Sewing Machine YouTube
Threading a Janome sewing machine isn’t difficult, but if you’re a beginner it might take a few tries until you get the hang of it. As such, here’s a step-by-step guide from a Janome customer service representative to help you thread your machine correctly.
Start by lifting the presser foot, then moving the thread guides on the machine to the left. Place the spool on the thread stand, and then pass the thread through the upper thread guide. Move it over the thread tension discs and guide it into the lower thread guide. Next, pass the thread through the take-up lever, then follow the same path back up to the thread tension discs. Finally, move the thread guides back to the right and thread the needle.
When that’s done, pull the thread out at least 10 inches, and you’re ready to use your sewing machine again. Keep in mind that the spool of thread should always be placed so the thread rolls off clockwise when spinning the handwheel. Finally, remember to pull the thread from the spool when threading the needle, instead of unwinding it from the spool.
How to Adjust the Tension on a Janome Sewing Machine YouTube
Adjusting the tension on a Janome sewing machine properly is paramount in order to get the desired results. That’s why it’s a good idea to understand the basics of this process and adjust the tension when needed. According to a Janome customer service representative, here’s how to proceed.
Turn the machine off and unplug it before you start. Then, check the upper tension disks to make sure they’re the same size. If they’re not, replace one or both of them with the same size you have available. Move the upper tension disks midway between the tightest and loosest settings, as this setting is usually ideal for most fabric types and threads.
After that, adjust the lower tension disks according to what type of fabric and thread you’re working with. If your thread is too loose, you can tighten the lower tension disks until the stitch looks neat. Additionally, if the stitches on the wrong side are too loose, you may need to tighten both tensions. When the desired tension is achieved, test it on a sample of fabric and check the results.
Once you’ve adjusted the tension, you’re ready to get back to work on your Janome machine. However, if you’re still having issues, you may need to adjust the timing. Of course, it’s a good idea to contact your dealer if you’re feeling uncertain about this process.
How to Change the Needle on a Janome Sewing Machine YouTube
The needle of your Janome sewing machine should be replaced every time you start a new project, as incorrect needles can have a significant influence on the quality of your work. Thankfully, this task is quite simple, and you’ll find out below how to go about it.
First, unscrew the screw holding the needle in place and take it off. Remember to put the screw aside, as you won’t want to lose it. Then, pick the correct needle for your project – depending on the fabric you’re working with – and make sure the flat side of the needle is facing the back of the machine.
Place the needle into the needle bar and make sure that the eye of the needle is aligning as you turn it. When these two parts are properly aligned, you should feel a slight resistance when turning the needle. Push the needle all the way in, then screw the needle clamp back in place.
Finally, now is the time to bring the presser foot up by using the lever. At this point, you’re ready to start your project with your Janome machine. If you have any issues with the needle not going all the way in the bar, reach out to your dealer for additional guidance.
