Sewers all over are in agreement, there’s nothing worse than having to learn how to put a bobbin in a Janome Sewing Machine. But proper threading of the bobbin is essential for the successful output of your project. With a few tips and tricks, you too can be threading your Janome like a pro in no time!
Understand Your Machine
To thread a bobbin properly, you’ll need to first become familiar with the placement of the spool pin and bobbin winder on your Janome machine. All Janome models have these components, which are typically located near the top right corner of the machine.
Once you’ve found the spool pin and bobbin winder, you can start winding the bobbin. To begin, insert the bobbin onto the bobbin winder shaft; the bobbin winder shaft should be pointed toward the open end of the bobbin. Winding the bobbin starts the thread onto the bobbin, and it’s important to always wind the thread in the same direction to avoid tangles.
Thread the Bobbin
Thread the Janome sewing machine by inserting the end of the thread from the spool into the hole in the bobbin. Then, pass the thread under the tension clips to the left of the bobbin and back up through the level below the tension clips. Continue winding the bobbin as if it were a spool of string, wrapping the thread around the bobbin continuously until it is full.
Let go of the thread and hold onto the bobbin to keep the thread from becoming tangled. Once the bobbin is full, push it onto the bobbin winder shaft and give it extra tension by holding the thread taut until it is completely pulled into place. Remove the bobbin and trim the thread.
Insert the Bobbin in the Janome Sewing Machine
Now it’s time to insert the bobbin into the Janome sewing machine. Place the bobbin into the bobbin case, making sure that the thread is running in the same direction as the arrow on the case. Then, insert the bobbin case into the machine and make sure that it is secure in place.
Bring the thread to the front of the machine by lifting the needle onto its highest point and rotating the wheel at the side of the treadmill in a clock-wise direction. Move the thread over the take up arm, then to the left of the bobbin case, and then underneath the thread tension dial. Hold onto the thread gently to ensure the thread does not slip.
Hold the Thread Taut
To ensure proper tension, hold the thread taut by pulling it down and to the right until it snaps back up. Then, turn the wheel on the side of the sewing machine counter-clockwise until the needle moves down and to the left. Pull the thread through the hole in the bobbin case, then raise the bobbin case and the needle will catch the thread.
It is essential that the tension be just right. If it is too tight, the thread can break or the stitching will be tough. If the tension is too loose, the thread may not be able to stitch properly and the fabric may bunch up. A golden rule is to follow the directions included with the Janome sewing machine, as every model is slightly different and needs to be wound differently.
Check the Thread Direction
Once the bobbin is properly threaded, check how the thread is flowing from the bobbin case. Make sure that the thread is running in the same direction as the top thread. If it is not, adjust the tension and rewind the bobbin.
Finally, ensure that the entire thread is wrapped around the bobbin evenly, as this will help prevent the thread from tangling and bunching up. Once all of these steps are completed, you are ready to start using your Janome sewing machine and all the projects you can create!
Understand the Threading Tension Dial
A key component of threading a bobbin into the Janome sewing machine is the threading tension dial. This is the component that regulates the amount of tension on the thread. This is essential, as the thread needs to have just the right amount of tension to ensure that the stitches come out smoothly and consistently.
The tension dial is located on the top of the machine, near the spool and bobbin winder. It is marked with numbers, and the ideal setting for a Janome sewing machine is 5 or 8. To adjust the tension, turn the dial to the left to decrease the tension and to the right to increase the tension.
Thread the Needle
To finish threading the Janome sewing machine, you must also thread the needle. To do this, gently pull the thread from the bobbin to the front of the machine and slip the thread under the thread tension lever. Push the thread through the hole at the top of the needle, then wrap it around the upper spool pin and pull it back down. Make sure the thread is snug against the needle, then pull the thread one or two inches.
Now the top thread is ready to be used. A safety measure to ensure the thread is properly implemented is to pull the thread taut and make sure the needle is threaded correctly. Finally, press the foot pedal to check that the thread moves smoothly, and you’re all set to go!
Maintenance and Safety Tips
When threading a Janome sewing machine, it’s essential to follow a few basic safety tips. Be sure to disconnect the power cord when performing any maintenance, and take care when inserting the bobbin as it can cause the machine to malfunction if handled incorrectly.
It’s also important to clean the bobbin case regularly. This helps to ensure the thread does not become tangled and the fabric does not become stuck in the machine. You should also use the correct type of thread for the project at hand, as incorrect threads can cause jams and knots in the machine.
It’s also important to use the appropriate size bobbin for your Janome sewing machine. Different models take different sized bobbins; so make sure you check the size of the bobbin before buying it. Finally, always wear gloves when handling the bobbin to prevent the needle from piercing your skin.
Have Patience & Enjoy Your Sewing Journey
Learning how to thread the bobbin onto the Janome sewing machine can be a bit tricky, especially if you’re new to this endeavor. But with patience and a bit of practice, anyone can become an expert at threading their Janome machine. Plus, the thrill of finally achieving the perfect stitch can be truly rewarding.
For more advanced tips and tricks, finding a sewing instructor or joining a sewing class can provide helpful tips and tricks to quickly become an expert. As they say, practice makes perfect – so keep attempting to thread the bobbin! Soon enough, you’ll have the hang of it.
Uses of a Janome Sewing Machine
A Janome sewing machine can be used to create a wide array of projects, from clothing and accessories to home decor and crafts. Some of the most popular projects include quilting, knitting, patchwork, smocking and appliqué. Janome sewing machines come with a variety of accessories, such as feed-dog feet and walking feet, to help you create professional-looking projects.
If you’re looking for something a little bit more challenging, Janome also offers specialty machines such as embroidery and serger machines for those more advanced projects. Knowing how to put a bobbin in a Janome sewing machine is the key to unlocking an endless array of creative stitching possibilities.
Know Your Machine Inside & Out
In conclusion, learning how to thread the bobbin in a Janome sewing machine is an important step for any sewer. With knowledge of the basic components of your machine and a bit of practice, you’ll be stitching like a pro in no time!
Gaining a better understanding of the different components and mechanics of your machine, along with taking the time to research on tutorials, will help you become more familiar with the art of sewing. Ultimately, those skills will give you the freedom to take on more advanced projects and unlock your full creative potential.
