Sewing is a fulfilling and creative way to express yourself. For those just starting out, however, it can be quite intimidating. Bobbin winding and threading is one of the earliest steps of learning how to use a sewing machine and knowing how to put the bobbin in the right way is the foundation of successful sewing. In this article, we will discuss how to put bobbin in Janome sewing machine, an exceptional choice due to its user-friendly features and reliable construction.
To begin, ensure your machine is powered off. Start by removing the machine’s faceplate. On some models, the faceplate is held in place by a single screw situated at the top centre of the machine. The faceplate should then easily lift off. Inside the faceplate, you will find Janome’s convenient Quick-Set drop-in bobbin system, where you can easily drop the bobbin into place.
Next, hold the bobbin with the thread going in a clockwise direction. If the thread is going in the wrong direction, it won’t be possible to form a loop. This would increase the chances of the thread popping out. It is important to ensure the thread is travelling in the right direction to keep it tensioned and avoid any potential thread jam.
After you have ensured that the thread is travelling in the correct direction, you should place the bobbin in the hook on the machine, in the same way that it was taken out. Secure the hook and start pulling the upper thread towards the bobbin hook. This will make the hook start spinning and should always go in a counterclockwise direction. A simple way to make sure the hook is working in the correct direction is to rotate the wheel by hand. The hook must be spinning in the opposite direction.
Pull thread until the hook stops spinning and the upper thread passes through the needle plate’s small thread opener guide or hook. To make sure the hook spins in the right direction, check the back of the needle plate. Pull the upper thread enough to pass through the hook or guide and make a loop. The loop should face downwards. If the loop is not present, pull a bit more until the hook stops turning and passes the loop.
Finally, adjust the tension wheel, located on the front of the Janome machine. Put the wheel to the required tension, which will be determined by the type of fabric you are using. If the wheel is now turning, it is too tight. But if there is no tension, it is likely too loose. Adjust until you get a perfectly balanced wheel.
Now that the bobbin is placed in the Janome machine and adjusted to the correct tension, you are ready to begin your project. By doing all the steps mentioned above carefully, you can now correctly place the bobbin in Janome sewing machine and start sewing. Good luck and happy sewing.
Choosing The Right Bobbin
When learning how to put bobbin in Janome sewing machine, it is also essential to consider the type of bobbin you will be using. Firstly, you must be sure that the bobbin you intend to use is compatible with your machine. Otherwise, the bobbin will not function correctly, or worse, could cause damage to your machine. There are different kinds of bobbins, such as metal, plastic or magnetic. Each has its own advantages and it is important to ensure that the bobbin chosen is right for your machine and project.
Metal bobbins often cost more, but they are extremely reliable and hard wearing. They are perfect for heavier sewing and offer an even feed, making high quality stitching easier. Plastic bobbins are usually cheaper, but they can often lead to skipped stitches and tension issues, making them unsuitable for lighter and more delicate fabrics. Magnetic bobbins are ideal for computersized machines, as the metal hook secures the thread with ease, providing clear and accurate stitching.
In conclusion, you must choose wisely when selecting the bobbin for your Janome machine. Always ensure that the bobbin is compatible with your machine and the task at hand. With the right bobbin, your sewing will look professional and appear neat and even.
Revealing Janome’s Features
When learning how to put bobbin in Janome sewing machine, it is important to educate yourself on the features of the machine itself. Janome sewing machines are renowned for their user-friendly features and long-term reliability. One of their unique features is the automatic thread cutter. This cutter, which sews when the needle is all the way up, cuts the thread to save you the trouble of manual cutting.
Janome’s machines also feature built-in needle threaders, making it easier and faster to thread them. They also have a built-in one-step buttonholer, allowing you to create perfectly shaped buttonholes every time with no measuring required. The quick-release drop-in bobbin featured in Janome machines makes winding much easier and more convenient, taking the hassle out of sewing.
Janome’s machines also feature the AcuFeed Flex fabric feeding system. This system, which is exclusive to Janome, provides extra control when sewing more tricky fabrics like sheer material, jersey, and corduroy by guiding them more accurately, no matter how thick the fabric is. With this system, your Janome machine will provide virtually unlimited creative potential.
Tips and Tricks
When learning how to put bobbin in Janome sewing machine, it is important to use the right techniques and tricks. Firstly, never wind your bobbin while the machine is powered on, as this can lead to breakage. Additionally, always check your thread tension as this will determine the quality of your machine’s stitching. Remember that the tension should be balanced for best stitching quality. Finally, always make sure your machine has a full bobbin before working with a new thread. A low bobbin level can cause skipped stitches, which could result in a lot of wasted time and material.
In conclusion, correctly winding a bobbin in a Janome machine is one of the first steps to successful sewing. By taking the time to understand the machine’s features, choose the right bobbin and follow the right techniques, you can create perfect stitched garments and projects in no time.
Cleaning and Maintenance
Being aware of how to put bobbin in Janome sewing machine is only a small part of sewing. It is also necessary to understand how to properly clean and maintain the machine. First, dust off the machine and the bobbin compartment with a soft brush. This can be done after completing a project or any other time you feel something needs to be cleaned. Additionally, use a mildly abrasive cloth to clean the sewing machine’s exterior and avoid damp cloths as it could lead to damage to the machine.
It is also important to regularly oil your machine so that it functions properly. Oiling should be done every few months, or as prescribed by your Janome user manual. Follow the instructions to lubricate the feed dogs, main shaft and hook race carefully, as this is essential to ensure your machine works efficiently and lasts longer.
Finally, if something occurs such as thread breaking or jamming, never immediately open the bobbin case. To prevent the damage, unplug the machine first, so that the bobbin case can be opened safely. Following these cleaning and maintenance steps will prevent damages and ensure a longer lifespan for your Janome machine.
Understanding Troubleshooting
Whenever issues come up while sewing, they must be addressed immediately to prevent further damages. Being knowledgeable of Janome troubleshooting is essential in order to resolve any issues with your machine. Automatically check if the bobbin is inserted correctly and if the thread is wound the correct way. If you have done this and the issue isn’t resolved, you may have to consult the user manual for further information.
By reading up on the machine’s settings, you may be able to identify the issue with your settings and rectify it yourself. It is also useful to check forums and online tutorials to find out what other people are doing in the same situation. Remember to also make sure that the tension is set correctly and that the bobbin mechanism is clean and lubricated.
Sometimes the issue could be more serious and you may need to take it to a qualified sewist or technican. Make sure you choose a reliable and experienced repair service. If you do decide to use professional help, ensure that you have identified the issues as accurately as possible. This will save both time and money.
Conclusion
Putting a bobbin in a Janome sewing machine might seem like a daunting task at first, but by following these simple instructions and paying attention to details, it doesn’t need to be a stressful process. To ensure the highest quality output you must pay attention to the type of bobbin you use, the settings of the machine and even the tension of the thread. Following the advice and tips outlined in this article will enable you to correctly insert the bobbin in your Janome machine, so you can get to enjoy successful and fulfilling sewing experience.
