How to Thread a Consew Sewing Machine
Threading a Consew sewing machine can be a challenge, especially for beginning sewers. Sewing machines are precise instruments that must be correctly set up in order to function correctly. Taking the time to correctly thread the machine will save time and frustration later on.
The first step is to locate and identify all of the parts associated with threading the machine. If you are unfamiliar with the parts of your machine, it is helpful to look at the manual or watch online tutorial videos. Once you have identified all of the necessary parts, it is time to begin the process of threading.
Begin by raising the thread tension lever, which can be found on the top of the machine. Then, take a thread and insert it into the thread guide on the top of the machine. The thread should then be passed through the tension discs at the back of the machine, and then through the take-up lever. The thread should then be wound around the bobbin winder before passing through the take-up lever again and into the needle.
Now it is time to use the bobbin. Start by opening the bobbin cover, then slipping the thread onto the bobbin and pulling it through the slot in the bobbin cover. Follow this by winding the bobbin at the top of the machine, then replacing the bobbin cover. To finish, the presser foot should be raised, then the thread needs to be pulled and passed through the tension discs before replacing the presser foot.
Finally, the thread needs to be passed through the eye of the needle. If this is difficult, it can be helpful to use a needle threader. The needle should then be threaded through the tension device and the upper thread should be pulled and passed through the take-up lever. Pull the thread through until both threads are equal in length.
Check for Thread Security
Once the machine is correctly threaded, it is important to check that everything is in order. This can be done by raising the presser foot and lowering the needle. Pull the thread toward the back of the machine and it should pass through the tension device. If it does not, the thread may need to be adjusted.
Check that both threads are the same length, and that the upper thread is under the tension spring. If this is not the case, the thread tension may need to be adjusted. Finally, test the tension adjustment by sewing a seam and checking to see if the stitches are even.
Adjusting the Presser Foot and Needle Position
Adjusting the presser foot and needle position will help ensure that the stitch length and width are correct. To adjust the presser foot, loosen the screw at the back of the machine and move the presser foot up or down depending on the desired stitch length. To adjust the needle position, loosen the screw on the needle plate, then adjust the needle up or down depending on the desired stitch width. Tighten the screws again once the desired settings are in place.
Once the adjustments are complete, test the result by sewing a seam with the new settings. If the stitches are uneven or the tension is not correct, it may be necessary to adjust the settings again.
Checking the Stitch Length and Width
Once the presser foot and needle position have been adjusted, it is important to check the stitch length and width. The stitch length should be set at a number between 1 and 8, depending on the thickness of the fabric. The stitch width can be adjusted by turning the tension knob on the side of the machine.
Once the stitch length and width have been adjusted, test the settings by sewing a seam. If the stitches are even and the tension is correct, then the settings have been successful. If the stitches are uneven or the tension is off, then it may be necessary to adjust the settings again.
Check the Feed Dogs
Finally, it is important to check the feed dogs. The feed dogs are located at the bottom of the machine and they are responsible for propelling the fabric through the machine during sewing. To check the feed dogs, loosen the screw on the needle plate and lift up the feed dogs. If they are not properly aligned, they can be adjusted by turning the screw on the side of the needle plate.
Once the feed dogs have been adjusted, test the settings by sewing a seam. If the stitches are even and the tension is correct, then the settings have been successful. If the stitches are uneven or the tension is off, then it may be necessary to adjust the settings again.
Managing Thread Tension
Thread tension plays an important role in the quality of a seam, and it is something that should be managed carefully. Too much tension will cause the thread to be pulled too tightly, resulting in a tight and stiff seam, while too little tension will cause the thread to be loose, resulting in a gap between stitches. To avoid this, it is important to adjust the tension until it is at the correct setting.
Adjusting the thread tension is relatively simple, but it must be done with care. Begin by raising the thread tension lever and rotating the tension knob, located on the top of the machine. The tension knob should turn clockwise to increase the tension, and counterclockwise to decrease the tension. As you adjust the tension, test the settings by sewing a seam and adjusting the tension as needed until the stitches are even and the tension is correct.
Test the Machine Before Sewing
Once the settings have been adjusted, it is important to test the machine before beginning any sewing project. To do this, simply run the machine for a few stitches, and then observe if the tension is correct and the stitches are even. If the tension is off or the stitches are uneven, the settings need to be adjusted before continuing.
Adjusting the machine settings can take some time, but it is well worth the effort. Taking the time to properly set up the machine will result in better results when it comes time to sew. Once the machine is set up correctly, it is time to begin sewing and creating!
